| No. | Notes text |
| Notes Suspensions |
| A | If not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products. |
| The specifications indicated in the Components Certificate are for the classification of the item / vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter "K" in your vehicle registration certificate or to find at the type plate of your car!) |
| Please verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de |
| In case of non-conformance the items must not be fitted – please refer to your dealer. |
| Mounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online. |
| Mounting position - you can "read" the mounting position of the springs from the imprint - have them installed just the way you read the imprint. |
| Wheel adjustment - after completion of the spring/suspension installation, checking the wheel adjustment is required. |
| Shock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage. |
| The installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8 |
| Here all wheel/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required. |
| Depending on engine, gearbox/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. |
| The applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car. |
| If your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code. |
| 7 | The spring plates installed by the manufacturer are available at DB specialist workshops in sizes 8-23 mm. This allows to vary the lowering indicated here. |
| 9 | For tyre equipment 205/50/15 and rim 7J x 15. Recommendation: installation of sports gas pressure shock absorbers of similar construction. |
| 10 | Part number is available only from our special distributor. Please ask for availability and price. |
| 12 | For vehicles, not lowered by manufacturer. (OE-sport suspension) |
| 15 | Not fully equipped. |
| 16 | The special equipment mentioned below contents following point system: air-condition 7 points automatic-transmission (4+5 Cyl.) 4 points automatic-transmission (6 Cyl.) 2 points independent car heating 3 points sunroof 2 points ABS 2 points Airbag 1 point headlamp cleaning system 1 point engine skid plate 1 point electronic seat adjustment 2 points IF THE RESULT IS MORE THAN 4 POINTS ONE HAS TO CHOICE up to 7 points 8 mm (1 point rubber plate) up to 13 points 13 mm (2 point rubber plate) up to 21 points 23 mm (4 point rubber plate) More than 21 points the lowering Kit is for this version not possible |
| 18 | Without levelling control. |
| 19 | Vehicles with 6 cylinder engine require retrofit with sports shocks. |
| 20 | Except vehicels with 4WD. |
| 21 | Except electronic suspension systems. |
| 22 | In combination with Eibach suspension springs or original suspension. |
| 23 | Front and rear axle height adjustable by threaded strut. |
| 24 | Front axle height adjustable by threaded strut, rear axle by height adjustable unit. |
| 25 | In order to ensure sufficient clearance it may be necessary to use wheel spacers if the car is equipped with original wheel sizes. |
| 26 | When the car is lowered more than 40 mm in combination with a drive shaft diameter more than 42 mm, please make sure that there is sufficient distance between the stabilizer and the drive shaft. It maybe necessary to install another anti-roll bar or other coupling rod. |
| 28 | Only for vehicels with electronic drive-balance-control. |
| 30 | Height adjustment only according the measurements indicated in the Components Certificate. |
| 32 | Except models "Sportive" and Sport (models were are equipped with Bilstein shock absorbers) |
| 34 | Only for vehicles with front damper diameter of 55 mm |
| 35 | Only for vehicles with front damper diameter of 50 mm |
| 36 | For vehicles with EDC or 8-cylinder engines, additional add-on parts from the vehicle manufacturer are required: For the front axle: BMW part no.: Up to year 09/97 BMW Rep. kit 31 35 2 298 910, From year 09/97 BMW Rep. kit 31 35 2 298 911 For the rear axle (sedan only): BMW part no. Support bearing 33 521 091 710 + washer 33 521 092 986 |
| 37 | For vehicles with EDC or 8-cylinder engines, additional add-on parts from the vehicle manufacturer are required: |
| 38 | For the VA: BMW part no.: Up to year 09/97 BMW Rep. kit 31 35 2 298 910, From year 09/97 BMW Rep. kit 31 35 2 298 911 |
| 39 | for the HA (sedan only): BMW part no. Support bearing 33 521 091 710 + washer 33 521 092 986 |
| 42 | The spring travel dependent brake-pressure regulator at the rear axle has to be inspected and, if necessary, adjusted according to the workshop manual. |
| 44 | The original rear dampers have to be replaced by the supplied dampers. |
| 45 | In some cases additional OE-Parts for the installation of the suspension componends are required. Therefore please take a look at the corresponding technical documents which are available on our website. |
| 47 | The original rear dampers have to be replaced by conventionally dampers. |
| 48 | In the case of vehicle models with ride height control dampers (mark 2R or 4R) these must be changed to O.E. dampers with mark 1U or 3U, part number: 96 80 99 98, catalogue number: 48 06 443. |
| 49 | For vehicles with 4WD only! |
| 50 | Only for vehicles with 51mm front strut clamp. |
| 52 | Only for vehicles with single leaf spring. |
| 53 | Only for vehicles with double leaf spring and single leaf with distance part. |
| 56 | Vehicles with combined fog- and running lights have to be checked whether the height of the lower edge of the light is not closer than 350 mm to the ground. In this case additional running lights have to be mounted higher thand 350 mm. The original running lights have to be decomissioned by removing the bulbs an the cable connection. |
| 58 | not suitable for model "Cross" |
| 59 | Only for vehicles with following characteristics: front axle: steel spring, rear axle: levelling control |
| 60 | excluded Colt Rallyart up to 2009 |
| 61 | strut fixing with screw M14 (4-hole wheel attachement) |
| 62 | strut fixing with screw M16 (5-hole wheel attachement) |
| 63 | from supplement 14 |
| 65 | Please check your VIN: this kit fits: 10th character=letter (A, B, ...) |
| 66 | for 5-Seater |
| 67 | for 7-Seater |
| 68 | Increased axle-load when using trailer (see Components Certificate). |
| 69 | If a national individual type Components Certificate exist, it is necessary to approve a modification acceptance according to §19/2 StVZO. |
| 71 | without type: 1.6 Racing (DS3) |
| 72 | Part number is available only from our special distributor. Please ask for availability and price. Contact: Autohaus Haese GmbH , phone: 06134-18290, mail: info-mz@autohaus-haese.de, web: www.autohaus-haese.de |
| 73 | front wheel drive |
| 74 | original spring plate must be used |
| 75 | without AC (Air-Condition) |
| 76 | thread dimension: M12 |
| 77 | outer diameter front strut 45 mm |
| 78 | Due to the usage of gas pressure technology of the B6 / B8 dampers the dimension of lowering / lifting may vary slightly vehicle-specifically. Functionality of electronic dampers is not applicable . - If available, we recommend to use Pro-Tronic. |
| 79 | coilspring inner diameter 116mm |
| 80 | coilspring inner diameter 106mm |
| 81 | without 3. row of seats |
| 82 | distance between fixing holes front 58mm |
| 84 | not available for vehicles with xenon headlights (any mounting for the self-levelling headlamp system at the dampers) |
| 85 | thread dimension: M16 |
| 86 | short wheel-base |
| 87 | without off-road type |
| 88 | standard suspension |
| 89 | thread dimension: M10 |
| 90 | thread dimension: M14 |
| 91 | with drum brake |
| 92 | with disk brake |
| 93 | only for vehicles with base axle |
| 94 | only for vehicles with plus axle |
| 95 | only for struts, which are screwed together |
| 97 | without 1BH (Off road package) |
| 98 | with coil spring suspension |
| 99 | outer diameter front strut 47 mm |
| 101 | Once the suspension kit is installed the electronic damper control will not be available anymore. You will see a trouble code. This can be re-programed by an official garage/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code. |
| 102 | For campmobiles |
| 103 | up to chassis number: 200011 ; up to chassis number: 3B-YE121222 |
| 104 | up to chassis number: 3B_YE121221 |
| 106 | up to chassis number: 41999999 |
| 107 | up to chassis number: 48999999 |
| 108 | up to chassis number: 4B-Y-200000 |
| 109 | up to chassis number: 4D-Y-020000 |
| 110 | up to chassis number: 8D-1-030000 |
| 111 | up to chassis number: 8D-1-030001 |
| 112 | up to chassis number: 8D-X-200000 |
| 113 | up to chassis number: 8E-2-400 000 |
| 114 | up to chassis number: 8E-5-400 000 |
| 115 | up to chassis number: 8E-7-400 000 |
| 116 | up to chassis number: A394035 |
| 117 | up to chassis number: YS3ES55CD1 |
| 118 | for type: Avantgarde |
| 119 | for type: Avantgarde, Elegance |
| 120 | except type: JC Works GP |
| 121 | except tpye: "iL" |
| 122 | for type: G02 |
| 123 | for type: G02, GT, GTI |
| 124 | for type: G07, G08 |
| 125 | for type: G07, G08, G09, G11 |
| 126 | for type: G07, G08, G09, G11, GT, GTI |
| 127 | for type: G29, G30 |
| 128 | for type: M 030 |
| 130 | for type: without EDC (electronic damper control) |
| 131 | from chassis number: 199008-> 199209 |
| 132 | from chassis number: 199210 -> |
| 133 | from chassis number: 3B-YE121222 -> |
| 134 | from chassis number: 4B-1-000001 -> |
| 136 | from chassis number: 4B-W-070001-> 4B-Y-200000 |
| 137 | from chassis number: 4D-1-000 001 -> |
| 138 | from chassis number: 51000001 -> |
| 139 | from chassis number: 8D-1-030000-> 8D-W-006471 |
| 140 | from chassis number: 8D-1-030001 -> |
| 141 | from chassis number: 8D-1-030001 ->;from chassis number: 200007 -> |
| 142 | from chassis number: 8D-W-006471-> 8D-1-030000 |
| 143 | from chassis number: 8D-X-200000 -> |
| 144 | from chassis number: 8D-X-200001-> 8D-1-030000 |
| 145 | from chassis number: 8E-2-400001 -> |
| 146 | from chassis number: 8E-5-400 001 -> |
| 147 | from chassis number: 8E-7-400 001 -> |
| 148 | from chassis number: A394035 -> |
| 149 | from chassis number: A394036 -> |
| 150 | from chassis number: F054768 -> |
| 151 | from chassis number: YS3ES55CD2 -> |
| 153 | not for distribution in China (Taiwan) |
| 154 | only in combination with Bilstein Teile-Nr. / part-no. 50-174546 (deactivation module for electronic dampers)- only available at Bilstein: mail: info@bilstein.de / Tel: +49 (0) 23 33 / 7 91-4444 |
| 155 | only in combination with BMW part-no. 31 32 1 139 423 (2x) - only available as BMW-OE-parts (stoneguard) |
| 156 | only in combination with BMW part-no. 31 33 1139 436 - only available as BMW-OE-parts (top mount) |
| 159 | without EDC (Electronic Damper Control) |
| 160 | If replacement required: You will find the components in the Components Certificate at the point "Amendment of the vehicle documents". The Components Certificate can be downloaded on: www.eibach.com - click on British flag - Online Catalog / Product & Components Certificate Search (RED BUTTON) |
| 161 | If replacement required: Please contact your dealer. - Please have your car documents, part numbers and sales receipt ready to give detailed information. |
| 162 | Not for "Caddy Maxi" |
| 163 | "LPG-(liquefied petroleum gas)-system"-engines included! |
| 164 | only in combination with BMW part-no. 33 50 6 778 572 (2x) - only available as BMW-OE-parts (stoneguard) |
| 166 | Land of production: Great Britain |
| 167 | up to chassis number: 7L-9-045000 |
| 168 | Only for cars with PASM (electronic damper control). |
| 170 | For cars with independent suspension at the rear axle. |
| 171 | For cars with rear live axle. |
| 174 | Not for suspension strut at the rear axle. |
| 175 | For vehicle with electronic damper control. (Series). PRO-TRONIC suppresses the error message after installaton of dampers or coil-overs (B12/PSS) without electronic adjustable dampers. The functionality of electronic damper control is not applicable. PLEASE NOTE: If there occur any questions or problems with the PRO-TRONIC, a vehicle-diagnosis-journal is absolute required. Your garage is able to get this journal from your car. Without this journal the handling of your inquiry is not possible. |
| 176 | For vehicle with electronic damper control. (Series). PRO-TRONIC suppresses the error message after installaton of the coil-over-suspension (PSS/PSM). The functionality of electronic damper control is not applicable. The kit includes the PRO-TRONIC-unit. |
| 177 | Vehicle with electronic damper control (Series) require the PRO-TRONIC-unit AM65-20-030-01-22. Please order separately. |
| 178 | For "Crosstouran" |
| 179 | Vehicles of the category M1G (Offroad) must be reclassified as M1. |
| 180 | from chassis number: WAUZZZ8....11201 |
| 181 | for vehicles without AMG-suspension |
| 182 | for vehicles with AMG-suspension |
| 183 | not for "STI" |
| 184 | Spring plate may be changed! - Kit E8530-140 may require OE-Spring-Plate No. 1HO412341. Kits E8547-140 and E8550-140 may require OE-Spring-Plate No. 357412341A. |
| 185 | up to chassis number: KNEJC524875 644 788 |
| 186 | from chassis number: KNEJC524875 644 789 |
| 187 | from chassis number: WAUZZZ8....11201 |
| 188 | for type: G01, G02, 0N4 |
| 189 | for type: G01, G02, 0N1 |
| 190 | for type: G03, G04, G05, G06, G07, 0N4 |
| 191 | for type: G03, G04, G05, G06, G07, 0N1 |
| 192 | Only for vehicles without PASM (electronic damper control). |
| 193 | Only for vehicles without air suspension. |
| 194 | for type: ZFA, not for type 3C3 (USA) |
| 195 | not for type 3C3 (USA) |
| 196 | Damper length: FA: 564 mm, RA: 666 mm |
| 198 | Stabilizer diameter 20mm |
| 199 | Stabilizer diameter 21mm |
| 200 | for type: 0N9 |
| 201 | for type: 04N |
| 202 | for type: G46, G57, G10 |
| 203 | for vehicles with EDC (electronic damper control) |
| 204 | for type: G01, G04, 0N1 |
| 205 | for type: G01, G04, 0N4 |
| 206 | for type: G01, 0N1 |
| 207 | for type: G01, 0N4 |
| 208 | for type: G02, 0N1 |
| 209 | for type: G02, 0N4 |
| 210 | Only Export - nor available in Germany - only without Components Certificate! |
| 211 | long wheel base |
| 212 | Not for "Nürburgring-Edition" (211 HP) |
| 213 | Pigtail-end above |
| 214 | from supplement 13 |
| 215 | for vehicles without "OE Offroadpackage" |
| 216 | piston rod - thread M12 - For vehicle without electronic damper control. |
| 217 | piston rod - thread M14 - For vehicle with electronic damper control. (Series). The included blind plug suppresses the error message after installaton of the coil-over-suspension (PSS). In some cases an error message occurs in the error memory. - Therefore these blind plugs have been replaced by the new Pro-Tronic-kit AM65-57-004-02-22. |
| 218 | Part number is available only from our special distributor. Please ask for availability and price. Contact: Vmaxx GmbH & Co. KG , phone: +49(0)2103-334929, mail: info@vmaxx.de, web: www.vmaxx.de |
| 219 | Not for "Trailhawk" |
| 220 | Not for "2.0 R WRC" |
| 221 | For vehicles with "Sport-Select-Suspension". Rear axle mount has to be changed. - Please use the included rear axle mount and PRO-TRONIC. PRO-TRONIC suppresses the error message after installaton of dampers or coil-overs (B12/PSS) without electronic adjustable dampers. The functionality of electronic damper control is not applicable. |
| 222 | Not for "RS3" |
| 223 | Not for "OPC"/"VXR" |
| 224 | BOM = 1 pc. OE-replacement spring - We recommend always to change both springs of an axle. (2 pc.) To verify the correct spring, please search for the OE-part-No#. (e.g at our website, the TecDoc-cataloge or similar systems) |
| 225 | Not for "T32" (Vehicles with double bolt McPherson strut.) - Only for vehicles with strut-clamp. |
| 226 | for type: CB8 |
| 227 | for type: CEW |
| 228 | For vehicle with electronic damper control. (Series). Blind-plug-set suppresses the error message after installaton of dampers or coil-overs (B12/PSS) without electronic adjustable dampers. The functionality of electronic damper control is not applicable. |
| 229 | Brake disk diameter 266 mm |
| 230 | Brake disk diameter 302 mm |
| 231 | for gasoline engine with manual gearbox |
| 232 | for gasoline engine with automatic gearbox and diesel vehicle |
| 233 | only in combination with BMW part-no. 31 33 1 139 452 - only available as BMW-OE-parts (top mount) |
| 234 | not for "ABC" (Active Body Control) |
| 235 | For vehicle with electronic damper control. (Series). The functionality of electronic damper control will be preserved. |
| 236 | Only for vehicle with S-Line-suspension. (Audi) |
| 237 | Only for vehicle without S-Line-suspension. (Audi) |
| 238 | Only for "T32" - Vehicles with double bolt McPherson strut. - Not for vehicles with strut-clamp. |
| 239 | Vehicles with manual transmission |
| 240 | Vehicles with automatic transmission |
| 241 | Vehicles fitted to the HA with two leaf springs per side must be converted to a leaf spring. (For Caddy to Mod.2015 VW Part No .: Leaf spring 2K5 511 151 N; for Caddy from model 2015 VW Part No. 2K5 511 151 AA) |
| 242 | Diameter hole in dome: 33mm |
| 243 | Only for vehicles without Sport Suspension Plus and without DRC - Dynamic Ride Control |
| 244 | Only for vehicles with Sport Suspension Plus including DRC - Dynamic Ride Control |
| 245 | Distribution only by: www.eibach.com.au - Eibach Suspension Technology Pty Limited | 3/4 Prosperity Parade | Warriewood NSW 2102 | Australia |
| 246 | Not for "Tiguan Allspace" |
| 247 | Only for vehicle with Range-Extender. |
| 248 | Not for "CrossCountry" |
| 249 | Not for "Plug-in-Hybrid" |
| 250 | Not for "S3" |
| 251 | Not for "GT3, GT4" |
| 252 | Housing diameter in the clamping area: 49 mm |
| 253 | Housing diameter in the clamping area: 53 mm |
| 254 | Not for vehicles with R.S.-Sportsuspension |
| 255 | Not for 1.6 RS Trophy |
| 256 | for type: G02, G06, G25, G28, G29, G32, 0N4 |
| 257 | for type: G01, G02, G03, G04, G06, G25, G28, G29, G32, 0N4 |
| 258 | for type: G01, G02, G03, G04, G07, G16, G21, G24, 0N4 |
| 259 | for vehicle without AMG-Line Suspension |
| 260 | for vehicle with AMG-Line Suspension |
| 261 | for "Plug-in-Hybrid" |
| 262 | For vehicles with EDC additional fitting parts of the manufacturer is necessary: 31306792211 (coupling rod) |
| 263 | only for Lotus models with Toyota engine |
| 264 | Housing material aluminum |
| 265 | only for cars with 4-doors |
| 266 | Part number is available only from our special distributor. Please ask for availability and price. Contact: Hansen Styling Parts, phone: 04347-706970, mail: info@hansen-styling-parts.de, web: www.hansen-styling-parts.de |
| 267 | not for models with the sales name Wrangler with short wheel base |
| 268 | for cars without direct-shift gearbox (DSG) |
| 269 | for cars with direct-shift gearbox (DSG) |
| 270 | for cars without M1G-Approval |
| 271 | not for R.S. Trophy |
| 272 | Use in 2WD vehicles only in combination with automatic transmission |
| 273 | only for cars with PR-Code 1BV, 2MD, 2MH |
| 274 | only for cars with PR-Code 1BL, 1BQ |
| 275 | front axle up to chassis number: 3603471 / rear axle: without air suspension |
| 276 | front axle up to chassis number: 3603471 / rear axle: withair suspension |
| 277 | front axle from chassis number: 3603472 / rear axle: without air suspension |
| 278 | front axle from chassis number: 3603472 / rear axle: withair suspension |
| 279 | Only for suspension strut at the front axle (McPherson) |
| 280 | not for models with equipment line R-Design |
| 281 | Vehicles without automatic transmission |
| 282 | up to chassis number xxxxxxxxxJxxxxxxx |
| 283 | not for facelift models |
| 284 | for facelift models |
| 285 | Not for AMG-Models |
| 286 | For BMW models with factory designation F_ (eg F20, F30) and electronic damper force adjustment, the acceleration sensor must be properly shut down via the OBD interface. If required, we will let you know the reponsible Eibach partner for you. Please contact: Eibach Service Center, sales@eibach.de |
| 287 | not for Audi S4 TDI / MY 05.19 - |
| 288 | not for Audi S5 TDI / MY 05.19 - |
| 289 | Vehicle with electronic damper control (Series) require the PRO-TRONIC-unit AM65-35-029-01-22. Please order separately. |
| 290 | only for cars with PR-Code 0N1 |
| 291 | only for cars with PR-Code 0N4 |
| 292 | only for cars with PR-Code UC8 |
| 293 | only for cars with production date until 25.02.2019 and until FIN (vehicle identification number) 17 digit FIN at position 11 = letter K (production year 2019) 17 digit FIN at position 12 = letter K (production month February) |
| 294 | Part number is available only from our special distributor. Please ask for availability and price. Contact: Squadra Sportiva, http://www.squadra-sportiva.com, e-mail: shop@squadra-sportiva.com / phone: +49 4561-525310 |
| 295 | Delivery only possible via Mitsubishi Germany. If necessary, contact your authorized Mitsubishi dealer. |
| 296 | All petrol engines 2WD/4WD (4-matic) with OE sports suspension with SA950 or SA483 and all 2WD petrol engines with basic supension SA485 |
| 297 | All diesel engines 2WD/4WD (4-matic) with OE sports suspension with SA950 or SA483 and all 2WD Diesel engines with basic supension SA485 |
| 298 | Only for 4WD (4-matic) with basic suspension SA485 |
| 299 | Only for cars with Active Drive II |
| 300 | Distance of the mounting holes 58mm |
| 301 | Distance of the mounting holes 72mm |
| 302 | for vehicle variants M and L |
| 303 | only for cars with 2-doors |
| 304 | up to MY 12-2012 only in connection with 2x CV11-5414-AB (OE-part Ford) |
| 305 | for vehicles with a standard empty mass ≤ (less than or equal to) 1700 kg |
| 306 | for vehicles with a standard empty mass > (larger) 1700 kg |
| 307 | wheel base: 2890 mm |
| 308 | not for vehicle with AMG Trail Package |
| 309 | not for vehicles with bump-travel-dependent brake pressure reducers on rear axle (RA) |
| 310 | For following models optionally in connection with M45-20-045-01-01 (7mm) rubber plate on the rear axle: BMW 3 330e 2WD/xDrive (G20/G21) / BMW 3 M340i xDrive, 330d xDrive, M340d xDrive (G21) |
| 311 | without Porsche lift system on the front axle |
| 312 | Fixed setting of the groove adjustment on the rear axle: 2nd ring groove from below |
| 313 | Fixed setting of the groove adjustment on the rear axle: 3rd ring groove from below |
| 314 | for sales name VW T6 |
| 315 | for sales name VW T6.1 |
| 316 | for sales name VW T6 / VW T6.1 |
| 317 | not for vehicles with 19-inch original rims (with and without DCC) |
| 318 | reduced lowering by approx. 15 mm with 19-inch original rims (with and without DCC) |
| 319 | Only vehicles from the Tesla factory in Fremont, USA and VIN (vehicle identification number) 17-digit VIN at position 11 = letter F (Plant of Manufacture = Fremont, California, USA) |
| 320 | not for vehicles with Audi dynamic all-whell steering |
| 321 | Only vehicles from the Tesla factory in Shanghai, China and VIN (vehicle identification number) 17-digit VIN at position 11 = letter C (Plant of Manufacture = Shanghai, China) |
| 322 | Spacer plates M45-20-045-01-01 included in the scope of delivery are optionally provided for the use of BMW 3 Touring (F31) with a high curb weight (e.g. vehicles with glass roof). |
| 323 | The original Volkswagen rubber plate 5Q0 512 149 G (9mm) or 8J0 512 149 (13 mm) can be used optionally for vehicles with heavy equipment variants (e.g. rear wheel, trailer coupling, glas roof, etc.) - detailed information can be found in the parts certificate. This is an optinally exchange for the standard VW rubber plate 5Q0 512 149 F (6mm). Only available from Volkswagen dealers or original parts dealers. |
| 324 | Can only be obtained from Eibach China - eMail: eibach@eibach-china.com. This article does not include any parts certificate! |
| 325 | Different top mounts are used on BMW 5 E34. We recommend the use of following components: 1. top mount 2x 12-248605 2. Following BMW OE parts depending on the year of construction: until MY 04.93: 31336776760 and 31331128524 from MY 04.93: 31332227342 and 31332227348 |
| 326 | wheel base: 2755 mm |
| 327 | Depending on the standard chassis, the amount of lowering is reduced by: SA-Code: B59 Dynamic Select / -0mm 459 Dynamic Body Control / -5mm 485 comfort chassis / -0mm 486 sports suspension / -15mm 677 Agility Control / -15mm |
| 328 | Wheelbase 2670 mm |
| 329 | Not for vehicles with equipment line Wildtrak |
| 330 | Not for "Overland" |
| 331 | Not for vehicles with OE-suspension SA code 459 (Dynamic Body Control - chassis with adaptive dampers) |
| 332 | only for vehicles with OE-suspension SA code 459 (Dynamic Body Control - chassis with adaptive dampers) |
| 333 | Part number is available only at Eibach China. Please ask for availability and price - contact details: Eibach Springs Taicang Ltd., No. 63 Ningbo Road, Taicang 215400 / e-Mail: sales@eibach-china.com, phone: +86 (0) 512 8278 1666, fax: +86 (0) 512 8278 1660 |
| 334 | Wheelbase 2785 mm |
| 335 | Wheelbase 2975 mm |
| 336 | only for vehicles with AMG ACTIVE RIDE CONTROL (470) |
| 337 | Wheelbase 2989 mm |
| 338 | only for vehicles without winch on the front axle |
| 339 | only for vehicles with winch on the front axle |
| 340 | for manual and automatic transmissions |
| 341 | PR-Code 1JP |
| 342 | PR-Code UB1 |
| 343 | Fixed setting of the groove adjustment on the rear axle: 1st ring groove from below |
| 344 | PASM standard / PR code 1BH |
| 345 | PASM sports suspension / PR code 1BV |
| 346 | incl. lift system / PR code 2UH |
| 347 | For vehicles with and without lift system (equipment code 479) |
| 348 | wheel base 3100 mm |
| Notes Wheelspacer |
| AS | You have to consider the requirements of the Components Certificate. Our approvals are available on www.eibach.com |
| Our wheelspacers are produced in consideration of the original wheels. When using acessory- or specialwheels, you have to check, if these wheels comply with the necessary requirements. Expecially on cars with studs/nuts. Further we point out, that the larger the wheelsize is, the sensitively reacts the steering in relation to vibrations. (Often caused by badly balanced wheels.) In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. - The information in the Eibach installation instructions must always be observed. |
| § 21-acceptance - In Germany and other European states it is necessary to approve wheelspacers by a Components Certificate-organisation. If this is necessary in your country, please contact your nearest test center to get more information about requirements and costs. |
| Spacers should always be fitted by hand. - The use of an electric or pneumatic screwing tool should be avoided, as this may result in the spacer not sitting optimally on the centering and thus to undesirable vibrations when driving. The use of paints, varnishes, lubricants and separating agents on the contact surfaces of the spacers or the wheel mounting parts is not permitted, as this can lead to the failure of the parts and subsequently to personal injury and damage to property. |
| The use of steel wheels in combination with Pro-Spacer-wheelspacers is prohibited. |
| Components Certificate (ABE) - Regarding to the regulations of the Federal Motor Transport Authority, the Components Certificate (ABE) only is valid in combination with bolts delivered by Eibach. |
| Existing center- and assembling-aids at the wheel hub have to be removed. (e.g. fixing bolts, clamps or rings of the brake disk or -drum) |
| S1 | When using 15mm wheelspacers there at least have to be 14 mm minimum cut-outs in the wheel to take up the original bolts (when using 20mm spacers 9 mm minimum cut-outs, when using 25mm spacers 4 mm minimum cut-outs). If this isn´t the case shorter bolts must be used. (System 5, 6 ) Otherwise the use of the spacers is not allowed. |
| S2 | Except for model R5 (Tdi) - because of bolt pattern 5/120 |
| S3 | Only for use on the front axle! |
| S4 | For vehicles with (accessory) wheels without cut-outs. |
| S5 | For vehicles with a centre stud height up to 17,5mm. |
| S6 | Only for use on the rear axle! |
| S9 | ATTENTION - ALSO NOTE ON SERIES WHEELS! - When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is not possible to use the wheels or wheelspacers! Please check as follows: Stud lengh (e.g. 25mm) minus spacer-thickness (e.g.15mm) = 10mm exess length. So the cut out should have 11mm depth to take the original stud. Further the cut out should have minimum 22mmx22mm height/width to take the overlaping nut. It´s allowed to shorten the stud bolt with a saw (Maximal up to the beginning of the nut. - We recommend only to shorten the minimum lengh.) If shorten the stud bolts, first please consider that all wheels used at the car still will fit (e.g. summer- / winterwheels) ATTENTION: when using 15 mm wheelspacers at least 7 mm deep cut-outs are needed (at 20mm wheelspacers at least 2mm deep cut-outs are needed) as the nuts stand over the contact surface! It´s allowed to shorten the stud bolts |
| S10 | For vehicles with a centre stud height up to 12,5mm. |
| S11 | The centering of the wheel is only possible with the wheelbolts! Therefore, it can be necessary to do a wheel balancing on the car, to avoid possible vibrations. |
| S12 | Due to the gradation of the wheel centre, a centering of the wheelspacer cannot be guaranteed with some models. |
| S13 | With some models, it is only for use on the front axle as the centering of the wheel stud on the rear axle is too long. Fits up to 16mm centre bore height! From production-No# 161225 -> (Please note the printing on the spacer!) also suitable for VW UP!, Seat MII, Skoda Citigo rear axle as changed to 17mm centre bore height! |
| S15 | When using system 3/7 (50mm), the original wheel bolts can be too long. In this case, they must be changed to shorter bolts. |
| S16 | Mazda / Nissan / Subaru have various wheel studs that are dependant on the model, axle or year they were built in. Before ordering, please check on both axles, what knurl diameter the original wheel studs have. In our kits, we include wheel studs with a knurl diameter of 14,9mm (14,3mm for Subaru). Other knurl diameter sizes need to be indicated when ordering! |
| S17 | For vehicles with a centre stud height up to 16mm. |
| S19 | For vehicles with sliding doors, it needs to be checked if wheelspacers of 25mm / 30mm can be installed. |
| S20 | Not permitted for vehicles with a lightweight suspension (Type 6E, Lupo 3L Tdi, Lupo FSI) |
| S21 | The steering angle possibly needs to be limited. |
| S22 | In combination with spacer rings, an 18-inch wheel/rim- combination is only permitted if the wheel has been already approved by the Components Certificate as original equipment. |
| S23 | Not permitted for vehicles with steel wheels! |
| S25 | Cannot be installed with some Turbo-models due to a changed centre stud. |
| S26 | With some models, it can only be used on the front axle as the grease-cap of the rear axle wheel carrier can stick-out too wide. The maximum height of the centre stud including the grease-cap is 10mm! |
| S28 | When using system 3/7, the origial screws have to be changed against shorter screws. Item-No for the use with original wheels: S4-7-14-50-28-19. When using acessory wheels, please fill out the Checklist. |
| S30 | The wheelcarrier has to be disassembled for changing the stud bolts. |
| S32 | Stud bolts needn´t be changed. |
| S33 | The original stud bolts must be changed. Longer stud bolts are enclosed in the kit. At some cars (e.g. Ford, Kia, Volvo) it´s necessary to disassemble the wheeltrunk and/or the wheel bearing. This only should be done by your garage. |
| S34 | When using system 3/7, the origial bolts have to be changed against shorter bolts. Item-No for the use with original wheels: S1-1-14-50-30-17. (Included in delivery) If using accessory wheels you have to check the mount of the wheels. If necessary you have to order shorter bolts. Please use our checklist. |
| S35 | When using system 3/7, the origial screws have to be changed against shorter screws. Item-No for the use with original wheels: S4-1-14-50-28-19 (Included in delivery) If using accessory wheels you have to check the mount of the wheels. If necessary you have to order shorter bolts. Please use our checklist. |
| S37 | When using the wheelspacers you have to verify that the wheels being used have suitable cut-outs to take up the original bolts. Without these cut-outs it is necessary to use the delivered studs in exchange to the original studs! - The original studs may optionally be shortened. |
| S38 | For vehicles with a centre stud height up to 18mm. |
| S39 | Not for use with 2005 standard-wheel (chrome-plated) |
| S40 | Only for use on models with tripartite center hub. |
| S41 | Not for use on models with US-Wheels, as these wheels don´t have the necessary cut-outs! |
| S43 | Year 20-05-2002 to 25-03-2004 please order 10 pc. S3-0-12-50-52-143 seperately when using for the front axle! |
| S44 | Year 20-05-2002 to 25-03-2004 please order 10 pc. S3-0-12-50-62-143 seperately when using for the front axle! |
| S45 | Please Note: As Mercedes uses different bolts you have to check that the bolt when put in the wheel mustn´t stand over more than 20mm. If this is the case you eighter have to use S90-2-20-007 (optionally S90-2-20-007-B) with longer bolts, or you have to order shorter bolts for fixing the wheel. In both cases please use the checklist! |
| S46 | This Kit includes additional wheelbolts to fix the wheel. When using this kit you have to use these wheelbolts as the original bolts are too long to fix the wheel. |
| S47 | The original bolts have to be changed against shorter bolts or cut to length. |
| S48 | Also for front axle use from production date 24-2006 (Marking 24E06 - Please note the printing on the spacer!) |
| S50 | Also for front axle use from production date 14-2006 (Marking 14E06 - Please note the printing on the spacer!) |
| S51 | Also for front axle use from production date 21-2006 (Marking 21E06 - Please note the printing on the spacer!) |
| S52 | Also for front axle use from production date 35-2006 (Marking 35E06 - Please note the printing on the spacer!) |
| S53 | Not for AMG-Models! |
| S54 | With some models, it can only be used on the front axle as the grease-cap of the rear axle wheel carrier can stick-out too wide. The maximum height of the centre stud 13,5mm! |
| S56 | Only to use from production date 28-2007 (Marking 28E07 - Please note the printing on the spacer!) . Earlier dates don´t fit the original wheels! |
| S57 | OEM wheels of these type may use different bolt length. Therefore you have to examine, what bolt lengh is used. Please fill out the checklist! |
| S58 | Citroen, Peugeot vehicles use different OEM wheels with different bolts. It´s necessary to check what bolts are used even if OEM wheels are used. Please fill out the checklist! |
| S60 | As the diameter of the center stud can vary, the wheelspacers only can be centered by the studbolts/nuts. |
| S62 | It´s necessary to modify metal parts of the inner wheel arch! |
| S66 | Not for vehicels with overstanding boltheads on the wheeltrunk, as these bolts mustn´t be dismounted. |
| S67 | When using 20mm System 7 spacers the wheelbolts mustn´t stand over more than 20mm out of the wheelhub. If this is the case the bolts have to be replaced with shorter bolts. (Please follow our installation instruction!!) |
| S71 | Also for front axle use from production date 33-2010 (Marking 146417 and following - Please note the printing on the spacer!) |
| S72 | Only for cars with Air-ride and levelling control |
| S73 | Only suitable if outer spacer diameter >165mm. - Suitable from production-no.# 161220 -> (Please note the printing on the spacer!) |
| S75 | From batch number 172158 (production February 2013 - pay attention to stamping on the spacer!> Article No. . Batch <) also suitable for the rear axle, if the grease cap on the rear axle is removed and inserted into the centering of the spacer! |
| S76 | If necessary, the grease cap has to be removed. |
| S77 | If there is a centering cover (grease cap), this must be removed from the wheel hub and placed on the spacer. |
| S78 | The hub will be enlarged by monting the centering ring. The grease cap has to be removed from the hub and mounted to the centerring ring. |
| S79 | Regarding the Components Certificate, please consider the maximum axle load. |
| S80 | From batch number 212294 (pay attention to stamping on the spacer!> Article No. . Batch <) also for models from model year 2015 onwards. |
| S81 | for vehicles with 14,9 mm knurl size (stud bolt) |
| S82 | for vehicles with 14,3 mm knurl size (stud bolt) |
| S83 | for vehicles with 13,0 mm knurl size (stud bolt) |
| S84 | Export article or in Germany only available without homologation! |
| S86 | This kit contains additional tapered flange wheel nuts with an extended shaft that must be used in place of the stock wheel nuts. The rim must not be fastened with the original wheel nuts when using the spacer, as the original wheel nuts are too short to allow sufficient fastening of the rim. If accessory rims are used, it must be checked whether the holes in the rim have at least 15mm for thread size M12 and at least 16mm for thread size M14. When using accessory rims that are attached with round head nuts, use of the Pro-Spacers is prohibited. Use with rims that are fastened with spherical collar nuts is not permitted with these nuts! |
| S87 | Only for AMG-Models! |
| S88 | Can be used for vehicles with a centering up to 16.00 mm height. From production week 11-2023 (from batch 292982) Can be used for vehicles with a centering up to 18.00 mm height. |
| S89 | Only when using rims with 7,5x45° internal chamber. |
| S90 | Suzuki have various wheel studs that are dependant on the model, axle or year they were built in. Before ordering, please check on both axles, what knurl diameter the original wheel studs have. In our kits, we include wheel studs with a knurl diameter of 12,9 mm. Other knurl diameter sizes need to be indicated when ordering! |
| S91 | Not for use with Hyper GT-wheel. |
| S92 | Only for models with 5-part centering. |
| S93 | Scout version without approval. |
| S94 | Only for vehicles with 31mm stud length - Not for vehicles with 26mm stud length (free length, measured from the wheel contact surface) |
| S95 | Not for aluminum rims with central locking optics. |
| S96 | Only suitable for stud lengths> 40mm. Measured from the wheel carrier. (up to year of construction 09-2020) |
| S97 | only for vehicles without 4CONTROL all-wheel steering |
| S98 | Note thread and centering! |
| S99 | Only when using rims with 4,5x45° internal chamber. |
| S100 | Only when using rims with 5x45° internal chamber. |
| S101 | Only when using rims with 6,5x45° internal chamber. |
| S102 | Only to be used from production week 11-2022 (identification 281111 or 45157097 and following (note the embossing on the spacer!))! |
| S103 | Only when using rims with 7x30° internal chamber. |
| S104 | Only when using rims with 4x45° internal chamber. |
