| No. | Notes text |
| Notes Wheel spacers |
| 1 | Excluding models with 4 wheel steering. |
| 2 | Excluding four wheel drive models. |
| 3 | Not for vehicles with electronic damper control. |
| 4 | Excluding models with automatic level control, or automatic level system can be adjusted in accordance. |
| 5 | Complete suspension kits are excluding models with automatic level control, please use our springset. |
| 6 | The front indicator lights on these vehicles must be relocated or replaced. These can be acquired from the manufacturer under order number 46226698. |
| 7 | Front axle height adjustable, rear axle consists of lowered sports springs and sports dampers. |
| 8 | In combination with original wheels and tyres, wheelspacers might be necessary. |
| 9 | Only for cars with a clamp diameter of 55 mm on the front axle. |
| 10 | Only for cars with a clamp diameter of 50 mm on the front axle. |
| 11 | Rear shock absorbers with eye-mounting. |
| 12 | Rear shock absorbers with fork-mounting. |
| 13 | We recommend a special anti roll bar kit (part no. ZB50-016/ ZB50-017 for models with a drive shaft diameter of min. 50mm. This is for improving the clearance of the right hand side drive shaft. Because of car specific differences a clearance is not always given. |
| 14 | Not for cars from 2004 onwards with standard 16“wheels. |
| 15 | The lowering rate will be reduced for models with original sports suspension. |
| 16 | On the front axle struts you need to measure the whole distance of the lower mounting drills. This distance has to be 72mm. |
| 17 | Please replace the anti-sway bar kit on max. TÜV tested lowering. This is for enough clearance of the right drive shaft. Anti-sway bar kit for cars without Xenon headlights: part no. ZB50-016 Anti-sway bar kit for cars with Xenon headlights: part no. ZB50-017. |
| 18 | Please use different top mounts for models with a year of construction earlier than 6/92 (BMW part no.: 31336764947; disk 31331116983; nut 31331110196). |
| 19 | On the front axle struts you need to measure the whole distance of the lower mounting drills. This distance has to be 58mm. |
| 20 | Rear axle shock absorbers are not atjustalbe for dumping. Sport shock absorbers with a harder dumping characteristic will be supplied. |
| 21 | Only for 4 wheel drive models (4x4, 4motion, Quattro etc.). |
| 22 | Only for vehicles where the rear shock absorber is attached at the bottom with an M14 bolt. |
| 23 | or 8cyl. engine are required from the automobile manufacturer: for the front: (BMW Part No.: To My. 09/97 = 31 35 2 298 910, Till My. 09/97 = 31 35 2 298 911), for the rear: (BMW Part No.: dome bearing 33 521 091 710 + washer 33 521 092 986). |
| 24 | For the rear axle sport shock absorbers will be supplied, the factory air spring will maintain. The lowering of the vehicle needs to be done according to the instructions. |
| 25 | At vehicles equipped with electronic damping DCC, the electronic damping control needs to be deactivated. |
| 26 | At vehicles equipped with audi magnetic ride, the electronic damping control needs to be deactivated. |
| 27 | At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. |
| 28 | not for vehicles with Xenon headlights. |
| 29 | Additional attachments are required from the automobile manufacturer (for the Fiat Bravo/Brava only available for vehicles with original sport suspension). Fiat Part No.: support bearings 00046469709 + strut insulator 00046448102 |
| 30 | Vehicles with a two-part leaf spring on the rear axle have to be equipped with a one-piece leaf spring. (up to mod.2015; VW part no. for leaf spring spring 2K5511151N; from mod.2015-; VW part no. for leaf spring spring 2K5511151AA) |
| 61 | Only for vehicles where the rear shock absorber is attached at the bottom with an M10 bolt otherwise use article no. 11560012. |
